Page Title

Der Wiki wird derzeit überarbeitet: neue URL, neues Design, neue Inhalte!

Benutzer-Werkzeuge

Webseiten-Werkzeuge


mikeurban:setup:installation_2016_neuin2016

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen Revision Vorhergehende Überarbeitung
mikeurban:setup:installation_2016_neuin2016 [2017/03/13 18:35]
thomas
mikeurban:setup:installation_2016_neuin2016 [2017/03/13 18:39] (aktuell)
thomas
Zeile 46: Zeile 46:
     * Flood Screening Tool (FST) – vereinfachte und schnellere numerische Lösung ermöglicht schnellere Berechnungen für effiziente Überflutungsbetrachtungen((siehe Handbuch "​CollectionSystem.pdf",​ Kapitel 9.3.1 "​Choosing 2D model"​))     * Flood Screening Tool (FST) – vereinfachte und schnellere numerische Lösung ermöglicht schnellere Berechnungen für effiziente Überflutungsbetrachtungen((siehe Handbuch "​CollectionSystem.pdf",​ Kapitel 9.3.1 "​Choosing 2D model"​))
  
 +
 +===== MIKE URBAN 2016 Service Pack 3, November 2016 =====
 +
 +^  Modul/​Typ ​ ^  Fehler/​Neues Feature ​ ^  Status ​ ^
 +|  MIKE 1D |Infiltration flow and wetting loss reservoir have been improved for the Kinematic Wave (B) runoff model|Fixed|
 +|  MIKE 1D |Improved handling of catchment with extremely low slopes. A limit of 1 per mille has been set as lower limit|Fixed|
 +|  MIKE 1D |MIKE 1D MU-RR: RDI+A/B with dedicated rain has been assigned correctly|Fixed|
 +|  MIKE 1D |The engine has been enhanced to extrapolate CRS section when water level are higher in open channels|New Feature|
 +|  MIKE 1D |A validation check has been added, enforcing that Colebrook White is only valid for circular cross sections.|Fixed|
 +|  MIKE 1D |Coupling of basin and soak-away nodes to 2D is now possible with MIKE1D|Fixed|
 +|  MIKE 1D |Runoff model B result file has been optimized to create significantly smaller results and running faster by means smart dry time stepping implementation|Fixed|
 +| Model Manager |An exception has been eliminated when importing links with topology ticked|Fixed|
 +| Model Manager |Catchment connection wizard includes Soak-away nodes|Fixed|
 +| Model Manager |Specification of units during import process has been enabled.|Fixed|
 +| Model Manager |Calibration plots and reports tool has been updated to handle network res1D results.|Fixed|
 +| Model Manager |Pipe Design Wizard has been enabled to create an ADP file for the mode “Individual”|Fixed|
 +| Collection system |Problem with importing data from KMD2 files has been fixed.|Fixed|
 +| Collection system |Import of SWMM5 DWF patterns with //​“hourly”//​ and //​“weekend//​” types into MIKE URBAN have been corrected|Fixed|
 +| Collection system |The tool to convert SWMM Interface files to CRF files has been updated. As well as a problem reading SWMM.out files in the SWMM converter has been fixed|Fixed|
 +| 2D Flooding |MIKE URBAN Flood can load dfs2 results file when the time zone is set to Sydney time, which caused some problems before.|Fixed|
 +| 2D Flooding |A problem with MIKE1D interpreting an internal node as an open boundary node  has been resolved|Fixed|
 +| MOUSE engine |MOUSE Engine should issue an error message if the field ’Discharge coeff’ in the Orifice dialog is left empty|Fixed|
 +| MOUSE engine |MOUSE/MSHE coupling has been updated|Fixed|
 +| Water Distribution |Improved checked of program files.|Fixed|
 +| Water Distribution |Handling of pressure units’ conversion has been improved.|Fixed|
 +| Documentation |Updated information on LID control units.|Fixed|
  
 ===== MIKE URBAN 2016 Service Pack 2, April 2016 ===== ===== MIKE URBAN 2016 Service Pack 2, April 2016 =====
mikeurban/setup/installation_2016_neuin2016.txt · Zuletzt geändert: 2017/03/13 18:39 von thomas