Benutzer-Werkzeuge
mikeurban:setup:installation_2014_neuin2014
Inhaltsverzeichnis
Neu in MIKE URBAN Version 2014
Modellmanager
Datenbearbeitung und Dateiformate
- Based on ArcGIS 10.1
- Improved navigation for large networks by the use of the Network Overview Mode
Erstellen und Pflegen von Modellen
- Improved Model Configuration tool (sorting and filtering, improvement of the log file)
- Change in the Simplification tool to keep the RTC elements
- Improved Result Verification tool
- Creation of a tool to display disconnected loads
Speziell für die Kanalnetzberechung mit MOUSE oder MIKE 1D
MIKE 1D
- Possibility to view MIKE 1D Results in MIKE URBAN
- Ability to run an Advection-Dispersion (AD) simulation
- CRF-files can be use as input for a MIKE 1D Network simulation
- Possibility to export MIKE URBAN database in a .m1dx-file read by MIKE 1D engine
2D Overland Flow
- Possibility to save Flux result type
- 2D Outputs dialogue can be accessed from '2D result' button found under the "Network parameter" tab of the Computation dialogue
- 2D Outputs are saved in a folder named Result Files
- Flood map animation is smoother
Speziell für die Kanalnetzberechung mit SWMM5
- Possibility to partially load SWMM5 results.
MIKE URBAN 2014 Service Pack 3, Februar 2015
Please note that the service packs are accumulative, i.e. corrections and fixes released with a previous service pack are included in the newest service pack as well.
| Module/type | Error/Inconvenience/New feature | Status |
| Editing | * Changing language would leave the TOC un-translated unless the .mup file was saved * When splitting a pipe, the slope of the downstream pipe would sometimes be set incorrectly | Fixed |
| MOUSE | * Multiple MOUSE engines reading the same CRF file at the same time would result in a crash. Now, an appropriate error message has been included and the engine will not crash * Flap gate specified for a weir close to an outlet did not have any effect on the model initialisation. This has been fixed | Fixed |
| MIKE 1D | * Fixed potential crash when running LTS simulations with max inflow conditions | Fixed |
| EPANET | * Redistribute button in Demand Statistic did not work correctly when changing the simulation period * Fixed situation where the engine would not get the list of nodes when "Use all nodes" was selected for the Fire Flow analysis * Fixed problem when using GDB database and selections during * Fire Flow analysis Fire flow results could sometimes change if the set of nodes included in the simulation changed (the active selection) | Fixed |
| Results | * The name of result comparison layers now reflects the two results being compared * Fixed crash when loading DFS2 files with German ArcGIS installed | Fixed |
| MIKE FLOOD | * The diverted runoff is now included in the summary for coupled simulation. This helps to interpret the continuity balance | Fixed |
| Tools | * A potential crash when merging catchments was fixed | Fixed |
| Misc | * Increase maximum process size on 64 bit Windows. MIKE URBAN can now use upt o 4 GB of memory on 64 bit Windows. This allows loading of larger result files * Using a selection list in LTS job list generation now works * Configuration of longitudinal profiles with flags would sometimes remove lines in the list of lines. This has been fixed * MOUSE errors when coupling to MIKE SHE will now be properly routed to MIKE SHE * Removed option to import .mex files since this only worked for old .mex files. * Report time that node water level is above critical level in the HTML summary file | Fixed |
MIKE URBAN 2014 Service Pack 2, September 2014
Please note that the service packs are accumulative, i.e. corrections and fixes released with a previous service pack are included in the newest service pack as well.
To use Fire Flow for more hydrants in one time (simultaneously), a change to the database is required. This change is not included in SP2 but will have to be applied manually. This can be done from within MS Access: Add the following field to the mw_fireflow table:
- Field name: UseSimultaneousNo
- Date Type: number (Integer)
or from within ArcMAP:
- Start ArcMap
- Add mw_fireflow table from the model you want to use for simultaneous fire flow
- Open the table from the Table of Contents
- Click "Add Field" using the Table toolbar
- Define the following properties for the new field: Name: "UseSimultaneousNo", Type: ShortInteger
- Close the table and close ArcMap
| Module/type | Error/Inconvenience/New feature | Status |
|---|---|---|
| Editing | * Selection file for load allocation is not working * 2D results dialog are not synchonized with the simulation dialog when opened * SWMM: Disable the SideSlope field when the Weir type is V-Notch * The Place option to connect several Load Allocations is not working * Simulation Duration and End time spontaneously change without warning | Fixed |
| Import/Export | * Export of pump capacity curve with power does not respect the unit * PCS: Support of Excel 2010 is required to handle more than 63 pumps | Fixed |
| Longitudinal profile | * Problem with longitudinal profiles when more than one Result File is loaded * LP is wrongly displayed: Diameter is much too large | Fixed |
| MOUSE | * WATS Module is using the wrong slope in the equations * Coordinates used for rainfall boundary not used correctly * If an outlet is connected to a pipe with negative slope then water is filling up the network from the outlet. * The option ALTERNATIVELOWFLOW = 1 is per default activated when running a 1D simulation but not a 1D-2D * MU MOUSE LTS: if hot start is used, standard result file must be saved * Error reading hotstart file wrong causes the simulation to becomes unstable * Undefined error occurs when using water age boundary without water age simulation * Errors in implementation of Hydrogen Sulphide feature | Fixed |
| EPANET | * Pump field (mw_Pump.Par6) is not exported correctly (Comma/Dot issue) * Cannot run Fire Flow for more hydrants in one time (simultaneously) * Wall thickness calculation wrong * Fire flow setting dialog enable / disable logic errors * Minimum residual pressure is very high when it should be zero * The Rule based control does not access the comma as decimal separator | Fixed |
| Results | * Random series added to Results TS drawing * Wrong units shown for Water Quality results files from MOUSE engine * Displaying Time Series based on a selection displays more time series than it should * Crash when using selection set for loading results | Fixed |
| Demands | * "Reset existing node demands" doesn't work in "Assign demands to multiple demands" | Fixed |
| MIKE FLOOD | * Using decimals for the cell size creates incorrect and inconsisten dfs2 when running 1D-2D overland simulation * Cannot run a 2D overland flow simulation because the Coarse bathymetry is not generated correctly | Fixed |
| Tools | * Result verification fails when trying to compare res1d and .PRF files * "Regenerate catchment connections" fails to generate correctly specified catchment connections * The result Statistics are not correctly calculated on a Result Comparison * Model Configuration: The tool reports diffferences that are not there | Fixed |
| Misc | * Scenario manager name not properly updated in the window's title bar after changing active scenario * Runoff model B behaves diferently in MU 2012 and 2014 than it did in MU 201 * Error when using a combination of 'AD' simulation and 'CRF file' connected through the Boundary Connection Item specification | Fixed |
MIKE URBAN 2014 Service Pack 1, April 2014
Please note that the service packs are accumulative, i.e. corrections and fixes released with a previous service pack are included in the newest service pack as well.
| Module/type | Error/Inconvenience/New feature | Status |
|---|---|---|
| Editing | * Digitize rectangle functionality can cause a crash * Unselect nodes does not work after loading selection * When editing elements in for example link table in the "show selected" mode, editing becomes unavailable after changing forth and back * Possible crash when creating a link (from the map) with Polish language * The visualization of the BC in the TOC is not updated when adding a new BC | Fixed |
| Import/Export | * Selection files would select random nodes when node IDs in the selection file do not exist * Cannot add a dfs2-file in ArcMap * Cannot export msm_BItem to Excel * Missing Item type for Time series * Possible crash when loading selection file | Fixed |
| Longitudinal profile | * Link diameter sometimes set to very high value * Each time you run a simulation and load the results, two new grphical items are added in the Longitudinal Profile * Save layout will incorrectly save result file names * It is possible to draw a profile through disconnected pipes | Fixed |
| MIKE 1D | * License check in the MIKE 1D control module if only MIKE URBAN LinkRegulation and WellSetPoint are used * Runoff Sensor is not supported * Error check for catchment discharge calculations detects problems associated with a Rainfall Runoff model | Fixed |
| MOUSE | * Simulation Summary, Spilling Node table: Remove "Surcharge" and "RDII Overflow" columns if not being calculated * ST calculation can hang when a pipe becomes filled by sediment * LTS simulation: Job list generation fails for specific rain data format * Error in initialisation of pressurised network and number of gridpoints in gravity pipes * The accumulated mass values of AD components reported by MOUSE are incorrect * Blocking time in MOUSE RTC does not work correct for Valves | Fixed |
| EPANET | * PID algorithm not working properly * Fire flow Q-H curve to be computed for partial range * Extended period simulation: Progress informatioon not displayed on the simulation prgress pop-up window * Importing a .inp duplicates the Tank and Reservoir if the Mixing is specified * Boundary condition cannot correctly display in map * Fire flow setting dialog enable / disable logic errors | Fixed |
| Results | * Cannot load results if the time step for saving the results is set to 0,083h | Fixed |
| Demands | * Cannot regenerate the Load allocations and Demand allocations connections | Fixed |
| Tools | * Catchment Processing failing with a specific polygon shape * The show Connected Catchment tools does not check that a node defined in the catchment connection does actually exist * Trimming does not work with GDB-setup * Result Verification with MIKE 1D results: the 'Set Max time' does not work * Result Verification can shows difference for two identical PRF files * Rename a scenario does not update the scenario name in simulation ID | Fixed |
| Misc | * M11extraWin tool: Command line arguments for Additional parameters are handled correctly * The license system memory consumption causes crashes when used very intensively, such as for operational systems * Crash for a general SQL command * Documentation: Change the coefficient of the Lag Time formulation | Fixed |
mikeurban/setup/installation_2014_neuin2014.txt · Zuletzt geändert: 2016/05/18 11:58 von julian
